|
|
Comlete design of class D power amplifier
Bistrý, Jan ; Šotner, Roman (referee) ; Petržela, Jiří (advisor)
In this bachelor's project was at first described a principle of class D power amplifiers. There was performed a characteristic of particular blocks. In the concrete steps were described particular solutions of these amplifiers with PWM driver, amplifier as an IC chip and were described advantages of this topology. It was performed an overview of the modern integrated amplifiers which are currently available. According to further requirements of this bachelor's project were designed a scheme and a board of printed circuit for this amplifier. In more details were described possibilities of output LC filter and performed its simulation. At the conclusion of this project was performed a laboratory measurement of realized amplifier which verified its performance and compliance with engaged parameters.
|
|
|
Electronic ballast for sodium lamp
Eliáš, Jaroslav ; Vorel, Pavel (referee) ; Huták, Petr (advisor)
The aim is to get acquainted with the way the management and regulation of sodium lamps. This knowledge is then applied to design your own gear. The introductory section describes the basic characteristics of discharge light sources. Their behavior was verified by measuring and findings were used to create diagrams, mainly the control circuit. Theoretical design is developed by individual functional parts of the inverter.
|
|
|
MIG/MAG welder with switching power supply
Klejma, Michael ; Červinka, Dalibor (referee) ; Martiš, Jan (advisor)
This diploma thesis deals with design of welding power supply for MIG / MAG and MMA technique with continuous output current 120 A. The first, theoretical part is devoted to welding process technology, physical characteristics of electric arc and description of individual welding methods. The thesis also deals with the concept of power converter. The design of the switched-mode power supply is based on a full bridge topology. In order to implement advanced controls of welding power supply, the ARM Cortex M4 microprocessor was selected. Due to the large power consumption of the stepper motor for drive the welding wire, an auxiliary switched-mode power supply was also implemented. The documentation describing the realization of the welding power supply and the results of the measurements are in the last part of the thesis. The welding power supply was successfully revived and reached nominal parameters. Inert gas welding has not been tested yet, due to lack of time caused by extensive work in order to complete mechanical realization.
|
|
|
Electronic ballast for sodium lamp
Eliáš, Jaroslav ; Vorel, Pavel (referee) ; Huták, Petr (advisor)
The aim is to get acquainted with the way the management and regulation of sodium lamps. This knowledge is then applied to design your own gear. The introductory section describes the basic characteristics of discharge light sources. Their behavior was verified by measuring and findings were used to create diagrams, mainly the control circuit. Theoretical design is developed by individual functional parts of the inverter.
|
|
|
MIG/MAG welder with switching power supply
Klejma, Michael ; Červinka, Dalibor (referee) ; Martiš, Jan (advisor)
This diploma thesis deals with design of welding power supply for MIG / MAG and MMA technique with continuous output current 120 A. The first, theoretical part is devoted to welding process technology, physical characteristics of electric arc and description of individual welding methods. The thesis also deals with the concept of power converter. The design of the switched-mode power supply is based on a full bridge topology. In order to implement advanced controls of welding power supply, the ARM Cortex M4 microprocessor was selected. Due to the large power consumption of the stepper motor for drive the welding wire, an auxiliary switched-mode power supply was also implemented. The documentation describing the realization of the welding power supply and the results of the measurements are in the last part of the thesis. The welding power supply was successfully revived and reached nominal parameters. Inert gas welding has not been tested yet, due to lack of time caused by extensive work in order to complete mechanical realization.
|
|
|
Optimization of switching regulated DC-DC converter design
Appel, Daniel ; Ing. Jan Bartoň, Meatest, s.r.o (referee) ; Hejátková, Edita (advisor)
The main goal of this project was an optimization of DC-DC converter design from company Meatest with regards to its efficiency, minimalizing power loses and radiated electromagnetic inference, while maintaining its price on reasonable level. The first part of this paper is introduction to the most common converter topologies. In the second part, design and optimization of converter are discussed. The third part is about measurement automatization in Simple. Measurements of converter prototype can be found in fourth part.
|
|
|
Comlete design of class D power amplifier
Bistrý, Jan ; Šotner, Roman (referee) ; Petržela, Jiří (advisor)
In this bachelor's project was at first described a principle of class D power amplifiers. There was performed a characteristic of particular blocks. In the concrete steps were described particular solutions of these amplifiers with PWM driver, amplifier as an IC chip and were described advantages of this topology. It was performed an overview of the modern integrated amplifiers which are currently available. According to further requirements of this bachelor's project were designed a scheme and a board of printed circuit for this amplifier. In more details were described possibilities of output LC filter and performed its simulation. At the conclusion of this project was performed a laboratory measurement of realized amplifier which verified its performance and compliance with engaged parameters.
|
guest ::
